Product Banner

Small PLC RX8U Series

img
img
img

Small PLC RX8U Series Overview

The RX series is the latest pulse PLC developed by Rtelligent. The product comes with 16 switching input points and 16 switching output points, optional transistor output type or relay output type. Host computer programming software compatible with GX Developer8.86/GX Works2, instruction specifications compatible with Mitsubishi FX3U series, faster running. Users can connect programming through the Type-C interface that comes with the product.

  • Up to 16 in and 16 out, output optional transistor or relay output (RX8U series only optional transistor)
  • Comes with a Type-C programming interface, usually equipped with two RS485 interfaces, one CAN interface (RX8U series CAN interface is optional)
  • The RX8U series can be extended to 8 RE series IO modules, flexibly expanding IO according to requirements
  • Instruction specifications are compatible with Mitsubishi FX3U series
icon icon
Connect With Us

Naming Rule

RX8U
1 -

32
2 M
3 T
4

  • Series Name
    RX3U: 3 axis pulse
    RX8U: 8 axis pulse
  • Input & Output points
    Input & Output point total 32 points
  • Module type
    Universal master controller module
  • Output type
    R : Relay output
    T : Transistor NPN output
RX8U-32MT
Input voltage DC24V. Voltage range : 20.4–28.8V, Voltage range : 20.4–28.8V
Pulse output 4 axis 200k, 4 axis 60k pulse output
Ontology IO count 16-point bipolar input (high shot entry points X0, X1, X2, X3, X4, X5, X6, X7 can only be shared positive)
IO Extensions 8 RE series modules
Isolation method photocoupling
Input impedance High speed input 2.4KΩ
Input is ON The input current of the high-speed input is greater than 5.8mA/24V/15VDC, 2.5mA
Input is OFF The high-speed input current is less than 4.5mA/19V
Filter function With filtering function, the filter range is 0–60ms can be set, the default is 10ms
High speed counting function Six single-phase 60K channels or AB phase 2 30K channels. X0/X1/3/4 is capable of receiving up to 480K
Input level Drain type/source type, S/S connected to 24V is NPN, S/S connected to GND is PNP. High-speed counting only supports S/S with 24V
Isolation Isolation (field and logic) Isolation group, 500VAC, 1 min, see wiring diagram
Storage temperature -25°C to 70°C
Operating temperature 0°C to 55°C
Humidity 5% to 95% (no condensation)
Altitude -1000m to 2000m
Air Dustproof, non-corrosive, low salt spray, damp, dust fog, and other environments, S0, <0.5µm, Hs<0.1ppm, relative humidity <60%, no condensation
Insulation voltage/high voltage insulation DC500V above 2MΩ / End to ground 2200VDC, end to end to 1500VAC (1 minute)
Resistance to electrical interference Pulse with 50ns, repetition frequency 5kHz, 2kV voltage peak/noise voltage 1kV-p1us pulse for 1 minute
Electrostatic discharge Contact discharge: +4KV, air discharge: ±8KV
Electrical fast transient pulse group Power cable: 2KV, 5KHz Signal cable: 2KV, 5KHz (I/O coupling clip), 1KV, 5KHz (communication clip)
Vibration resistance Frequency 10~57Hz, amplitude 0.1mm; The frequency is 57~150Hz, the acceleration is 1.0g, 10 times in each three-dimensional direction
Impact resistance 15g, lasting 11ms, three shocks in three dimensions
Ground (FG) The third type of grounding (not common grounding with the strong current system)
square-plus-pattern

Inquiry Now

Scan the QR to call

RB Automation

Submit Inquiry for

×